IEEE1284_TRANSFER

Section: Functions (3)
Updated: 07/26/2009
Index Return to Main Contents
 

NAME

ieee1284_nibble_read, ieee1284_compat_write, ieee1284_byte_read, ieee1284_epp_read_data, ieee1284_epp_write_data, ieee1284_epp_read_addr, ieee1284_epp_write_addr, ieee1284_ecp_read_data, ieee1284_ecp_write_data, ieee1284_ecp_read_addr, ieee1284_ecp_write_addr - data transfer functions  

SYNOPSIS

#include <ieee1284.h>
ssize_t ieee1284_nibble_read(struct parport *port, int flags, char *buffer, size_t len);
ssize_t ieee1284_compat_write(struct parport *port, int flags, const char *buffer, size_t len);
ssize_t ieee1284_byte_read(struct parport *port, int flags, char *buffer, size_t len);
ssize_t ieee1284_epp_read_data(struct parport *port, int flags, char *buffer, size_t len);
ssize_t ieee1284_epp_write_data(struct parport *port, int flags, const char *buffer, size_t len);
ssize_t ieee1284_epp_read_addr(struct parport *port, int flags, char *buffer, size_t len);
ssize_t ieee1284_epp_write_addr(struct parport *port, int flags, const char *buffer, size_t len);
ssize_t ieee1284_ecp_read_data(struct parport *port, int flags, char *buffer, size_t len);
ssize_t ieee1284_ecp_write_data(struct parport *port, int flags, const char *buffer, size_t len);
ssize_t ieee1284_ecp_read_addr(struct parport *port, int flags, char *buffer, size_t len);
ssize_t ieee1284_ecp_write_addr(struct parport *port, int flags, const char *buffer, size_t len);
 

DESCRIPTION

This set of functions is for tranferring bytes in the relevant transfer mode. For ECP and EPP modes two types of transfer are possible: data and address (usually referred to as channel in ECP).

The supplied port must be a claimed port.

The supplied buffer must be at least len bytes long. When reading, the transferred data is stored in the buffer; when writing the data to be transferred is taken from the buffer.

For reads (peripheral to host): if no data is available and F1284_NONBLOCK is not in effect, the inactivity timer is started. If data becomes available before the inactivity time-out elapses it is read; otherwise the return value will be E1284_TIMEDOUT.

For writes (host to peripheral): if the peripheral is not willing to accept data and F1284_NONBLOCK is not in effect, the inactivity timer is started. If the peripheral indicates that it is willing to accept data before the inactivity time-out elapses it is sent; otherwise the return value will be E1284_TIMEDOUT

The flags may alter the behaviour slightly:

F1284_NONBLOCK

For reads (peripheral to host): if no data is available, return immediately (with E1284_TIMEDOUT).

For writes (host to peripheral): if the peripheral is not willing to accept data, return immediately (with E1284_TIMEDOUT).

F1284_SWE

Don't use hardware assistance for the transfer, but instead set the parallel port pins according to the wire protocol.

F1284_RLE (for ECP only)

Use run length encoding. If the peripheral is in ECP mode with RLE, calls to ieee1284_ecp_read_data must set this flag in order for the RLE from the peripheral to be interpreted correctly, and calls to ieee1284_ecp_write_data may set this flag in order to take advantage of RLE.

F1284_FASTEPP (for EPP only)

Use multi-byte transfers. Several bytes at a time are transferred using hardware assistance, if supporting hardware is present. The price of this increased speed is that the return value will be less reliable when this flag is used.

For ECP mode, a given direction is in force at any particular time, and it is up to the application to ensure that it is only writing when in forward mode, and reading when in reverse mode.  

RETURN VALUE

The return value is the number of bytes successfully transferred or, if negative, one of:

E1284_NOTIMPL

This transfer mode and flags combination is not yet implemented in libieee1284.

E1284_TIMEDOUT

Timed out waiting for peripheral to handshake.

E1284_NOMEM

Not enough memory is available.

E1284_SYS

There was a problem at the operating system level. The global variable errno has been set appropriately.

E1284_INVALIDPORT

The port parameter is invalid (for instance, perhaps the port is not claimed).

If any bytes are successfully transferred, that number is returned. An error is returned only if no bytes are transferred.

For host-to-peripheral transfers, all data is at the peripheral by the time the call returns.  

SEE ALSO

ieee1284_ecp_fwd_to_rev(3)  

AUTHOR

Tim Waugh <twaugh@redhat.com>

Author.
 

COPYRIGHT


Copyright © 2001-2003 Tim Waugh